AirLive - Default Login Admin

AirLive Default IP

To access the admin page type 192.168.1.254 into your web browser's address bar or click on the link below.

Admin

Kredensial default untuk AirLive

100 %
IP Address:
192.168.1.254
Username:
admin
Password:
airlive

AirLive Router Login

Need to change your WiFi password or update your network settings? Log into your AirLive router's setup page to get it done.

The default gateway address for AirLive is 192.168.1.254. Type this into your browser's address bar (not the search bar) while connected to the router's network.

Langkah-langkah login

Accessing your AirLive router admin through http://192.168.1.254 will allow you to change the settings and configurations that your router software provides.

  1. Connect to your AirLive router. Make sure the router is on. Plug in an ethernet cable or connect to the router's WiFi. Ethernet works best for admin access.

  2. Open any web browser. Type 192.168.1.254 into the address bar (not the search bar) and press Enter.

  3. If the default IP doesn't work, find the real one. On Windows, open Command Prompt and type ipconfig. Look for "Default Gateway". On Mac, open Terminal and type netstat -nr.

  4. Use the default credentials listed above. The most common combo is admin / admin. Check the label on the bottom of your router if those don't work.

  5. You're in. Change your WiFi name and password, set up port forwarding, update firmware, or adjust security settings.

Pemecahan masalah AirLive Router Login

If you have forgotten your username and password, you can follow the instructions to recover them. If you haven't changed the default username and password that came with the router, you can consult our default router usernames and passwords list.

  • Can't reach the login page

    Make sure you're connected to the AirLive router via WiFi or ethernet, not mobile data. Type http://192.168.1.254 in the address bar. If it still won't load, unplug the router for 30 seconds and try again.

  • Default credentials not accepted

    Check the sticker on the bottom of your AirLive router. The actual username and password are printed there. If those don't work either, someone changed them. You'll need to factory reset.

  • Router stops working after changes

    Reset to factory defaults: hold the reset button on the back of your AirLive router for 10-30 seconds. Wait 2-3 minutes for it to reboot, then log in again.

  • Forgot the admin password

    A factory reset is the only way back in. This wipes all settings, including your WiFi name and password. You'll need to set everything up again after the reset.

  • Settings won't save

    Use an ethernet cable instead of WiFi when making changes. Some AirLive routers drop the connection during saves, which causes errors.

About AirLive Routers

AirLive started as a Taiwanese networking company in the early 2000s. The brand focused on wireless solutions for small businesses and home users across Asia. AirLive built a reputation for affordable wireless routers and access points that delivered solid performance without premium pricing.

The company expanded into security cameras and wireless adapters over the years. AirLive routers became popular in emerging markets where cost-effective networking solutions were needed. While not as well-known as major brands, AirLive maintained a steady presence in the budget router market.

Home users choose AirLive routers because they offer reliable wireless performance at competitive prices. The brand targets users who need basic networking features without paying for advanced enterprise functions they won't use.

AirLive routers come with straightforward web interfaces that don't overwhelm new users. The company designs their products for plug-and-play operation, which appeals to people who want working internet without complex configuration.

Accessing the AirLive Admin Panel

You can access your AirLive router admin panel through any web browser on your connected device. AirLive uses a standard web-based interface that works with Chrome, Firefox, Safari, and other browsers. The login process takes just a few minutes once you know the correct IP address and credentials.

Most AirLive routers use 192.168.1.254 as their default IP address. Type this address into your browser's address bar to reach the login page. Some older AirLive models might use 192.168.1.1 instead.

You can also find your AirLive router's IP address by checking the label on the device itself. Look for a sticker on the bottom or back that shows the default gateway address. If you're still unsure, open Command Prompt on Windows and type 'ipconfig' to see your default gateway.

AirLive routers sometimes take longer than other brands to respond to login attempts. Don't refresh the page immediately if it seems slow. Wait at least 30 seconds for the login page to load completely.

Some AirLive models have case-sensitive passwords even though the username isn't case-sensitive. Make sure you're typing 'airlive' in all lowercase letters. The brand also uses different default credentials on certain model lines, so check your router label if the standard login doesn't work.

AirLive routers may show timeout errors if you leave the admin page open too long. The system automatically logs you out after 10 minutes of inactivity for security. You'll need to log in again if you see connection timeout messages.

Popular AirLive Models

The AirLive WN-200USB series uses the standard 192.168.1.254 IP with admin/airlive credentials. These USB wireless adapters with router functionality were popular for their compact design. The WL-5460AP access point series also follows the same login pattern but may require 'admin' for both username and password on some units.

AirLive's AC series routers like the AC-1200R use the typical 192.168.1.254 address but sometimes ship with 'admin' and 'admin' as the default credentials. Check the label on your specific AC model to confirm. The older WL-1000AP series used 192.168.1.1 instead of the newer default IP.

The AirLive POE series combines power over ethernet with wireless capabilities. These models typically use 192.168.1.254 with admin/airlive but may have different credentials printed on the device label. Some POE models use numeric passwords instead of 'airlive'.

Newer AirLive router models from 2018 onwards use a blue and white web interface design. Older models show a basic gray interface with minimal styling. The login process works the same way, but the appearance differs significantly between generations.

AirLive's business-focused models often require different default passwords than home routers. These models may use the device serial number or 'password' instead of 'airlive' for the default login.

Troubleshooting AirLive Login Issues

If you can't reach the AirLive admin page, check that your device is connected to the router's network. Look for the AirLive wireless network name and connect using the password printed on the router label. Wired connections work best for accessing the admin panel.

AirLive routers sometimes need a power cycle to respond properly. Unplug the router for 10 seconds, then plug it back in. Wait 2 minutes for the device to fully boot before trying the login page again. The power LED should be solid green when ready.

AirLive routers ship with 'admin' as the username and 'airlive' as the password on most models. Some units use 'admin' for both fields instead. Try both combinations if one doesn't work. The password field is case-sensitive, so type 'airlive' in lowercase.

Check the white label on your AirLive router for the exact default credentials. Some models print custom passwords that override the standard 'admin/airlive' combination. The label may show 'Password:' followed by a random string of letters and numbers.

After factory resetting your AirLive router, wait 3 minutes before attempting to log in. The device needs time to restore default settings and boot completely. Use 192.168.1.254 in your browser with admin/airlive credentials. If these don't work, check your router model label for the specific default login information.

How to Factory Reset a AirLive Router

Factory reset your AirLive router when you've forgotten the admin password or if the device isn't responding properly. Reset also helps when you're selling the router or want to clear all custom settings and start fresh.

Find the small Reset button on your AirLive router, usually located on the back panel near the power port. The button sits recessed in the case, so you'll need a paperclip or pen tip to press it. Make sure the router is powered on before starting.

Press and hold the Reset button for 10 seconds while the router is running. Don't release the button too early or the reset won't complete. You should see the LED lights flash or turn off briefly during the reset process.

Keep holding the Reset button until the power LED starts blinking rapidly, then release it. The AirLive router will reboot automatically and restore factory defaults. The entire process takes about 2 minutes from start to finish.

Once your AirLive router finishes rebooting, connect to the default wireless network or use an ethernet cable. Open your browser and go to 192.168.1.254 to access the setup page. You'll need to configure your internet connection and wireless settings again from scratch.

Merek router terkait

Router Guides & Articles

Router Guides

Network Tools

Helpful Resources

Looking for a new AirLive router? Find AirLive routers on Amazon ›